Ohita ja siirry sisältöön
Beeswax Shampoo and Leave-in Conditioner

Beeswax Shampoo and Leave-in Conditioner

Making shampoo, and conditioner is easier than it sounds! Follow these instructions and realize how easy and amazing these products are for your hair.

Ingredients:

  • 2.3 grams of Solanum AX
  • 5 grams of Vegetable Glycerine
  • 5 grams of Coco-Glucoside and Glyceryl Oleate
  • 5 grams of Natra Prep Pea (pea extract)
  • 1 gram of essential oil (we suggest mint or peppermint)
  • 1 gram of honey
  • 1 gram of melted beeswax
  • 1.5 grams of Geogard Ultra
  • 1 gram of panthenol powder (vitamin b5)
  • 24 grams of Caprylyl/Capryl Glucoside
  • 15 grams Cocamidopropyl Betaine
  • 40.2 grams of distilled water
  • Scale
  • Beaker
  • Wisk
  • Shampoo bottle
  • Ph meter

Weigh the Solagum AX, glycerin, Lamesoft PO 65, pea extract, essential oil, Geogard Ultra, melted beeswax, honey, and panthenol (Vitamin B5) into a beaker and whisk/stir thoroughly to combine. Be sure the Solagum AX is very thoroughly distributed.

Add the Caprylyl/Capryl Glucoside and Cocamidopropyl Betaine. Stir slowly to combine. Mix well.

Gently add the water, pouring it over your stirring implement to break its fall. Gently stir the shampoo every 3 minutes for about 20 minutes. This helps the Solagum AX hydrate evenly rather than settling to the bottom and fusing into a solid lump that has to be aggressively stirred later on to incorporate.

Cover the shampoo, leaving the Solagum AX to fully hydrate and the Geogard Ultra to dissolve for about 2-3 hours.

Once everything has hydrated and dissolved, give the shampoo a stir to make sure everything is mixed well.

To test and adjust the pH create a 10% dilution by weighing 2g product and 18g distilled water into a small bowl or beaker and whisk to combine. Check the pH with your pH meter. Depending on the shape of your bowl/beaker you may need to tilt it to fully submerge the sensor on your pH meter. The pH should fall around 4.5. Aim for a range of 4–6 for hair health.

When the pH level is right you can add the shampoo to the bottle and use it.

Warning: If you have had the shampoo for a long period of time, look out for a smell, mold, discolor, or texture. If you see or smell this, please discard.

 

Leave in Conditioner

Ingredients:

  • 5-6 ounces of Coconut oil
  • 4 ounces of Shea butter
  • 1-2 ounces of beeswax
  • 1 ounce of argan oil
  • 1 ounce of jojoba oil
  • 6 drops of essential oil (optional)
  • 4 grams of Aloe leaf extract (optional)
  • Container

Directions:

  1. In a glass mason jar add the coconut oil, shea butter, jojoba oil, and argan oil into it. Put the jar in a pot with an inch of water on the lowest setting. Melt and stir together. Mix well.
  2. Add the beeswax. Start off with less until you get the consistency is the right texture for you. Mix well.
  3. Mix the essential oil, and aloe leaf extract together.
  4. Add it into a container.

Enjoy your homemade leave-in beeswax conditioner!

Article précédent
Article suivant
Fermer (esc)

Bee Part of the Hive

Get $25 off your first order along with regular discounts and educational content delivered to your inbox.

Age verification

By clicking enter you are verifying that you are old enough to consume alcohol.

Recherche

Panier

Votre panier est vide.
Boutique